Knowledge from the field of mechanical calibration

The methods for measuring pressure can be distinguished according to the underlying physical principles. A distinction is made between direct and indirect pressure measuring devices. A direct pressure gauge relates directly to the definition of the physical quantity of pressure; these include, for example, piston manometers and liquid manometers. Indirect pressure gauges make use of secondary physical effects and derive the pressure through them, i.e. they measure quantities, such as mechanical or electrical, which are clearly related to the pressure. These include, for example, pressure gauges with spring elastic measuring elements (Bourdon tube pressure gauges, diaphragm pressure gauges, etc.) and pressure sensors.

Pressure calibration

Basically, a distinction is made between spring-elastic and electronic pressure gauges. Pressure gauges with spring-elastic measuring elements combine high metrological quality, simple operation, robustness and adaptability with the advantages of industrial and cost-effective production. With spring elastic measuring elements, there is no need for complex electrical or pneumatic supplies. Electronic pressure gauges or pressure transducers are a widely used form of pressure sensing element. A pressure sensor is a measuring element which converts the physical measurand pressure into an electrical quantity.

Commonly used sensor methods are as follows:

• Thin Film Strain Gauge
• Ceramic thick film sensor
• Piezoresistive sensor element
• Piezoelectric sensor element
• Capacitive sensors

Absolute pressure (p abs)

• measured pressure above absolute zero
• Reference: ideal vacuum
• Measuring pressure always greater than reference pressure

Relative pressure (p rel)

• The relative pressure measurement measures the difference to the prevailing ambient pressure.
• This is dependent on various parameters (e.g. distance to sea level)
• Relative to this we speak of positive and negative overpressure

positive overpressure (gauge)

• measured pressure above the barometric daily air pressure
• Reference: Ambient pressure
• Measuring pressure always greater than reference pressure

negative overpressure (vacuum)

• measured pressure below the barometric daily air pressure
• Reference: Ambient pressure
• Measuring pressure always lower than reference pressure

Differential pressure (Δ p)

• measured pressure above or below any reference pressure
• Measuring pressure lower or higher than reference pressure

Calibration of pressure gauges can be performed according to different procedures. Which procedure is carried out depends on the class accuracy of the measuring instrument to be calibrated. Before measuring a series of measurements, a preload must be carried out to ensure that the complete pipe system is tight. Here pressure is applied to the measuring range end value of the device, after a holding time of approx. 30 seconds the pressure can be completely released again. If the pressure is unstable, the tightness of the pipe system must be ensured first; if the pressure is stable, calibration can be started. For this purpose, several measuring points (which are evenly distributed over the measuring range) are first approached from bottom to top (in the upward direction) and then also from top to bottom (in the downward direction). The holding times, measuring points and the number of preloads depend on the selected calibration sequence (A / B / C).

The following measuring systems are preferably used for the calibration of pressure measuring instruments:

• Pressure balances (piston manometers)
• Quartz spiral manometer
• Pressure calibrators and controllers

In our pressure laboratory we distinguish calibration according to two references: Pressure balances and pressure controllers. Pressure regulators have a high accuracy, can be automated, regulate the required pressures independently and are therefore ideally suited for the calibration of your working standards. For your reference standards, we use the more complex method of calibration by means of pressure balances. A pressure balance makes use of the physical property of pressure. The necessary pressure is generated with the aid of a mass disc and a piston/cylinder system. With this proven method, the necessary accuracy for the calibration of reference standards can be achieved.

Pressure calibration

For the calibration of torque spanners, mostly automatic and manually operated measuring stations are used. Here, the torque transducer rotates and thus introduces the desired torques into the tightening tool. The standard stipulates that this must be carried out at three different stages, depending on the test equipment, and must be repeated five times in each case. The currently valid standard DIN EN ISO6789:2017 clearly defines the test stages and covers the complete measuring range of the test equipment. The procedure for calibrating torque transducers deviates from this. Torque transducers are calibrated continuously, e.g. to exclude influences due to short-term creep. 

When calibrating rotation angles, a distinction is made between direct and indirect measuring systems. Direct measuring systems measure the angle of rotation via e.g. a glass scale. These sensors are installed in the calibration device as free of transverse forces and stresses as possible and the individual measurement series are run step by step. Indirect measuring systems are usually installed in torque spanners in the form of a gyroscope. For calibration, in addition to the angle of rotation, a torque must also be applied and maintained during the measurement.

The force measurement takes place in a material testing machine optimised for calibration, which has the necessary rigidity and also perpendicularity. Tensile and compressive forces can be applied and maintained in steps by means of rising and falling spindles. This calibration is characterized by a high degree of flexibility in the selection of measuring points. 

Force calibration

TEDS stands for ‘Transducer Electronic Data Sheet’. A TED is an electronic data sheet that is used in sensors or transducers. TEDS are subject to the IEEE 1451 standard. The most important information, such as manufacturer information, model numbers, measuring ranges and calibration data, is stored on the TED. This data can then be automatically read out and identified by the measuring system.

Yes, we at Testo Industrial Services are able to write to TEDS within several measurement variables such as pressure, acceleration and acoustics and can save essential data such as the sensitivity (the characteristic value) and the recalibration date on the TED. Because sensor data can change, it is important to keep the essential information up to date after calibration so that your sensor is ready for use again.

We support you with this:

Request offer